Views: 26 Author: Lilon Publish Time: 2026-11-20 Origin: Site
A black 48V e-bike charger sold in the UK has been recalled. The reason was not simply a faulty charging function. According to the UK's Office for Product Safety and Standards (OPSS), inspectors identified two separate defects involving the charger's internal mains wiring and its UK plug.
Published on 16 November 2026, the recall notice classified the product as presenting a serious risk. So, what exactly did the authorities find, and what does this case reveal about the requirements for chargers sold in overseas markets?

The recall concerns the following product:
| Item | Details |
|---|---|
| Brand | Chamrider |
| Model | 48V8A220VE |
| Product | Black e-bike charger |
| Sales period | 2 August–13 August 2026 |
| Country of origin | China |
| Risk level | Serious |
| Recall reference | 2609-0062 |
The recall is being carried out by EESA Star Limited. The OPSS notice advises owners to stop using the affected charger immediately and contact the company for a replacement or refund.
Read the official UK OPSS recall notice or view the official product recall report.
The official notice identifies two defects. They involve different parts of the product and different aspects of electrical safety.
The first issue was found inside the charger.
According to the OPSS report, the internal mains wiring was inadequately insulated and could come into contact with the accessible, unearthed metal enclosure.
If the wiring touched the metal enclosure, the enclosure could become live. This would expose a user touching the charger to an electric shock hazard.
The important point is that this defect concerns the construction and insulation of the mains-voltage section. It is not simply a problem with the charger's output voltage or charging performance.
The second issue concerned the fuse installed in the UK plug.
The OPSS stated that the fuse did not comply with the applicable requirements and might not provide the required level of protection in the event of an electrical fault.
This could allow the product to overheat and ignite, creating a fire risk.
Unlike the internal insulation issue, this defect relates to the plug configuration supplied with the charger for the UK market.

The recall highlights two separate areas that manufacturers and suppliers need to consider when preparing chargers for export.
First, the charger's internal design must be suitable for its electrical construction. Insulation between mains-voltage wiring and accessible conductive parts is a fundamental safety consideration. A product's external appearance or output rating cannot demonstrate that its internal construction meets the required safety standards.
Second, the plug and its components must meet the requirements of the destination market. A charger may use a different AC plug configuration depending on where it is sold. The plug, fuse and associated components therefore need to be assessed against the applicable national requirements.
The OPSS notice states that the recalled product did not meet the UK's Electrical Equipment (Safety) Regulations 2016 or the Plugs and Sockets etc. (Safety) Regulations 1994.
This distinction matters: checking the power supply itself is not the same as checking the complete product configuration supplied to the end user.
For manufacturers, exporters and distributors, the Chamrider case is a reminder that compliance needs to be considered at the level of the finished product and its intended market.
Several points are particularly relevant:
Review the complete product configuration. The charger, mains cable, plug and fuse should be considered as part of the supplied product rather than treated as unrelated components.
Keep market-specific versions under control. Different destination markets may require different plug types and component configurations. Changes should be documented and evaluated rather than treated as simple cable substitutions.
Link compliance documents to the actual model and configuration. Test reports and certification documents should correspond to the product being manufactured and supplied. A document for one configuration should not automatically be assumed to cover another.
Control component and design changes. Changes to internal wiring, insulation materials, plug assemblies or fuses may affect the product's compliance status and should be reviewed before mass production.
This recall concerns one specific charger model. It should not be taken as evidence that all e-bike chargers from a particular country or manufacturer have the same defects. However, it demonstrates why product-level verification and destination-market compliance are important in the charger supply chain.
Lilon ChargeTech manufactures external lithium battery chargers and AC/DC power adapters, with OEM/ODM options for output specifications, connectors, cables and product labeling.
For examples of external charging solutions used in electric mobility applications, see our 88W lithium battery charger for electric bicycles and scooters and 168W e-bike and scooter charger.
For any charger intended for export, the specific product design and destination-market configuration should be evaluated against the applicable requirements before supply.